Installing a hot water heater is a big job, but following some simple tips can make it go a lot smoother. Here are a few things to keep in mind:
Understand The Size Of The Hot Water System
When you are installing a water heater, one of the first things you need to do is understand the size of the hot water system in your home. That includes determining how much water flows through the pipes in a minute, and how many gallons of water are used in your household every day. To determine the size of your hot water system, you can use an online tool. You can also consult with a professional plumber who will be able to tell you the size of the hot water system in your home.
Gather Information About The Various Types Of Fuel
Before installing a water heater, you need to know what fuel source you want to go with. Do you want an electric geyser or a gas geyser? Electric geysers are perfect for people who are off-grid or don’t have access to natural gas. That being said, gas geysers are more efficient at generating heat. If you’re not sure what kind of fuel source you want to go with, consider the following information. A natural gas water heater is an efficient and cost-effective way to provide hot water for your home. You can also tie it into your existing gas line so installation is easier. When it comes to installing a propane water heater, there are a few things you should keep in mind. Keep in mind that propane water heaters run at a lower temperature compared to natural gas heaters. This is something to keep in mind when installing a water heater.
Space Around The Geyser
Geysers have warranties that can be voided if the hot water system is installed incorrectly. To make sure that doesn’t happen, you should leave enough space around the geyser to allow proper ventilation. The rule of thumb is to leave a gap of one inch on all sides. That includes the top and the bottom of the geyser, as well as the sides. This is to ensure that the heat doesn’t get trapped and does what it’s supposed to do heat the water.
Put The Water Heater At A Sufficient Height
Installing a water heater is all about keeping it accessible, but also keeping it safe. You want to keep it out of the way, but you also want to make sure that it’s not in a place where it can fall. Keep in mind that a water heater, fully loaded, can weigh between 150 to 200 pounds, depending on the size. There should be at least two feet between the floor and the bottom of the water heater. The water heater should also not be too close to an electrical panel.
Do Not Keep The Geyser Switched On For Extended Periods
When you first install your new water heater, make sure to turn the geyser on, but don’t leave it on for an extended period. Start by keeping it on for 15 minutes and then increasing the time by five minutes. After a few hours, you should be safe to leave it on. What you don’t want to do is keep the geyser on for days on end because that can cause damage. This is true for both electric and gas geysers.
Clean And Change The Filters Monthly
Like any other appliance in your home, you want to keep water heaters clean and maintained. One way to do that is to clean the filters on the geyser monthly. You can also do other maintenance tasks, such as changing out the spark arrestor, keeping the tank clean and free of sediment, and more. If your water heater is over 10 years old, consider replacing it. Hot water heaters last an average of 10 to 15 years. They can break down faster if you don’t maintain them properly. So, make sure to keep it clean and change the filters once a month.
Install A Tankless Water Heater
If you want to go all out, you can install a tankless water heater. This is a water heater that doesn’t have a tank, unlike a regular water heater. A tankless water heater is generally smaller and more efficient. It’s also more cost-effective compared to a regular water heater. There are a few things you should keep in mind when installing a tankless water heater. The first and foremost thing to consider is how much power you need. Different models of tankless water heaters have different energy requirements. When installing a tankless water heater, keep in mind that the distance between the water heater and the faucet should be at least six inches. You also need to install a pressure regulator to prevent water pressure issues.